Control panel. Related Manuals for Simon 3. Download Like. Full screen Standard. Page of 68 Go. Simon Security System. Plug the universal module into a wall outlet. Sensor Installation. Program sensors and devices before you install them. Use the following section to pro-gram the panel and add the sensors to panel memory. Entering Program Mode. Simon Security System User Guide. Simon Security System Security System pdf manual download. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Facebook; Twitter; LinkedIn; Comments. Previous Previous post: Bbq grillware ggpl manual. Contact the appropriate electrician or electric inspections authority. Do not attempt to make connections yourself. Contact the appropriate elec The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading.
The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed Load Number:.
Une note explicative sur les indices de charge voir 1. It may also be used to control lights and appliances within your home. The system has the capabilities of communicating with a central monitoring station and sending messages to a numeric pager. This manual describes how to operate your system. It will guide you through programming instructions for system features as well as basic arming and disarming commands for the system. The system is supervised, meaning that the panel checks the status of each sensor to detect problems.
If the panel detects trouble it will notify you with beeps and indicator lights on the panel itself. Your security system installation may include any of the following devices: Control Panel The Control Panel is used to operate and program your security system. It communicates to you through voice messages, beeps, and by lighting or flashing buttons. The panel can communicate to a central monitoring station, numeric pager, or both.
Touchpads Remote Handheld Touchpads are used to control the security system primarily from within the home. Keychain Touchpads are used to control the security system from within or near the outside of your home. Sensors Indoor Motion Sensors detect motion in a protected indoor area. When motion is detected the panel may respond by sounding chimes or an alarm. When motion is detected, the system may respond by sounding chimes or turning on outside lights. These sensors are not used for intrusion detection.
Smoke Sensors detect smoke and a significant rise in temperature. They have a built in siren that sounds when smoke or a significant rise in temperature is detected. Freeze Sensors detect furnace failure. Carbon Monoxide Sensors detect carbon monoxide. They have a built in siren that sounds when carbon monoxide is detected. Check with your installer for other applications. Audio Verification Module AVM is primarily used by the central monitoring station to monitor sounds and verbally communicate with a person inside the home.
This feature is similar to a speaker phone feature on a phone. Note The Master Access Code default is when the security system is shipped from the factory. You can enter commands for your security system through simple key presses on the panel. Depending on how your system is programmed, you may need to enter an access code for certain commands. An access code is a numeric code that allows authorization to operate your security system.
Control Panel Remote Handheld Touchpad This touchpad gives you the option to enter commands from any room in your house. You can enter commands through simple key presses on the touchpad. Dialog Touchtalk 2-Way RF Touchpad This touchpad gives you the option to enter commands from a remote location away from the control panel in your house.
It also allows you to hear panel messages when the System Status button is pressed. Keychain Touchpad Keychain Touchpads are handy for simple arming, disarming and light control functions. They are portable and can be carried off-site in a purse or pocket Telephone Touchtone telephones can be used to communicate with your system while you are offsite.
Ask your installer if you have this feature. Check with your installer to see if this feature is enabled.
The panel interface consists of four rows of buttons. The System Status button is used to give information on system activity. Environmental sensors, such as smoke and carbon monoxide stay active at all times.
System Status Press to hear information about your system. If the button is lit, there is a problem with the system. If the button is blinking, an alarm has occurred.
Press the button to hear what is wrong with the system. Exit Delay Exit Delay is the amount of time the system gives you to exit the home before the system is armed between 5 and seconds. This is programmed by the installer. Entry Delay Entry Delay is the amount of time the system gives you to disarm the system after entering the home between 5 and seconds.
If you close the designated door behind you when you exit, you will have to disarm the system upon reentering. Leave the designated door open while using the Quick Exit feature.
The Quick Exit feature is used when someone wants to briefly leave while the home is still armed i. This feature needs to be enabled by your installer. When you press the Disarm button the panel will announce exit time on. This will allow a designated exit door to be open for up to 2 minutes without triggering an alarm. Latchkey Latchkey is used to notify parents, via a numeric pager, if children do not arrive home at a predetermined time and disarm the system.
For example, you set the Latchkey time for pm. Subdisarm If your system includes hour protection sensors on items such as gun or jewelry cases, you must subdisarm the panel before accessing these areas to avoid causing an alarm.
Close all doors and windows. Enter Access Code if needed. Close all doors and windows except the ones you wish to remain open. Note Any sensors that are bypassed by the system will NOT be protecting your home. Note No Entry Delay can be used in two ways. To avoid causing an alarm, you must disarm the system with a remote handheld touchpad or keychain before entering your home. Check with your installer to find out how this option is programmed. Note This feature is most likely used when there is no one on the premises.
Panel announces any protected doors or windows that are open. Any sensors that are open when the system is armed will be bypassed automatically after exit. Panel announces, Doors and windows on, no entry delay. Press Arm Motion Sensors button once. Enter access code if needed. Panel announces, Motions on.
Arm Motion Sensors light will be lit and the exit delay will begin. Press the Arm Motion Sensors button twice. Panel announces, Motions on, Latchkey on. Arm Motion Sensors light will blink and the exit delay will begin. Upon reentering your home the entry delay will begin. Status beeps will sound. Enter your access code using the Code buttons. Panel announces, System disarmed and the Disarm light will be lit.
If you enter you home and you hear alarm sirens, or if controlled lights that should be off are on, an intruder may be inside or another emergency may have occurred. Leave immediately and call for help. Enter your Master Access Code while the system is disarmed. Panel announces, System disarmed. Disarm button light blinks and the system is subdisarmed. Disarm button light stops blinking. System is in Disarm mode. Check with your installer to find out if this feature is enabled for your panel.
If You Forgot Something After Arming Your panel can be programmed to recognize when you leave the premises then quickly reenter. The panel will restart the exit delay to give you time to collect your things and leave again. You must leave before the exit delay expires or disarm the system. Ask your installer if this feature is enabled for your system. Arming When the Panel Battery is Low Your panel may be programmed so that you cannot arm the system if the panel battery is low.
CODE Note 40 keypresses for invalid codes i. The alarm locks all touchpads, except keychains, for 90 seconds. Each button represents 2 numbers. Access code lengths need to be between 3 and 6 digits and are set by the installer. They are not used for intrusion protection.
If any of the Home Control buttons are Simon Security System 5 pressed and a sensor or module is not associated programmed with this feature the panel will announce, Function not available.
Chime Doors Chime Doors is used to signal chime when a protected door is opened while the system is disarmed. The panel will announce the door that has been tripped and chime twice ask your installer how this feature is programmed.
System must be disarmed. Press Chime Doors button. Panel will announce, Chime on. Chime Doors button will be lit. Press Chime Doors button Panel will announce, Chime off.
Note You can only use this feature if there is a Bypass button on your panel and there are no Special Motion Chime sensors in your system. Note You can only use this feature if there are no Special Motion Chime sensors in your system. This is used to detect movement within a specific area. These Motion Sensors are not used for intrusion protection. The panel will chime three times and announce see Option 41 the sensor that has been tripped. If you have Motion Sensors located in areas such as in a patio area or at the front door and you want to know when someone is approaching these areas, you would use this feature.
Direct Bypassing Direct Bypassing refers to turning off bypassing certain sensors while the system is armed. Press the Bypass button until you reach the sensor to be bypassed sensor must currently be unbypassed. Enter Master Code Direct Unbypassing Direct Unbypassing refers to turning on reactivating bypassed sensors while the system is armed.
Press the Bypass button until you reach the sensor to be unbypassed sensor must currently be bypassed. Enter Master Code. OR Change arming level. You can program what time the lights go on and off see Programming - Light Control.
Press Time Lights button. Panel will announce, time activated light on. Time Lights button will be lit. Panel will announce, time activated light off. Time Lights button no longer lit. Press Sensor Lights button. Panel will announce, sensor activated lights on. Sensor Lights button will be lit.
Panel will announce, sensor activated lights off. Sensor Lights button no longer lit. Controlling Individual Lights Lights with even unit numbers 2, 4, 6, 8 can be controlled from either the panel or a Remote Handheld Touchpad.
Lights with odd unit numbers 1, 3, 5, 7 can only be controlled from a Remote Handheld Touchpad. Lights with unit numbers cannot be individually controlled. Press Lights On button once. Press the number 2, 4, 6, 8 of the lamp module you want to turn on. Panel will announce, light on. Press Lights Off button once. Press the number 2, 4, 6, 8 of the lamp module you want to turn off.
Panel will announce, light off. Press Lights On button twice. Panel announce, Lights on. Press Lights Off button twice. Panel announces, Lights off. This feature silences the status beeps that accompany the exit delay see Status Beeps.
Press Chime Doors after you arm the system to silence status beeps. The panel will still beep at the beginning and end of the exit delay. Talk to your security system dealer to see if your panel has the AVM option.
Your system responds to you through the use of panel voice messages, status beeps, alarms, panel indicator lights, and to a numeric pager if programmed.
Panel Voice Messages When you press the buttons on the panel or the touchpads, the panel responds with voice messages. These messages may respond with system information or prompt you to take further action. Status Beeps Note You may receive a different number of status beeps if buttons are pressed quickly Status beeps are used to indicate key presses, status, and problems with the system. The following table describes status beep activity. Sirens are programmed by the installer to time-out and stop sounding after a specified time.
Use the following table to understand the siren sounds used by the security system. Temporal 3 refers to a continuous pattern of 3 siren pulses then off for 1. The system will send the message twice. Use the following table to determine what the numeric message is reporting. Most accidental alarms occur when leaving the residence after arming the system, or, before disarming the system upon your return.
Canceling Accidental Alarms There is a communicator delay Dialer Delay of 30 seconds programmed into this panel. The panel will delay 30 seconds before dialing the central monitoring station or a numeric pager to send reports. You can have your installer program this delay time between 0 - seconds. To cancel an accidental alarm before the programmed dialer delay time expires, enter your access code.
Guidelines for Preventing Accidental Alarms The following guidelines will go a long way toward preventing accidental alarms. Smoke detectors near bathrooms and kitchens can be tripped by steam and smoke from cooking. Call the panel and let the phone ring twice then hang up. Wait at least 10 seconds and call the panel again. You may wait up to 40 seconds before calling again.
The panel should answer on the first ring. At this point you may perform the actions listed in the following table of phone commands. CODE refers to the master and access codes programmed into your system. How to Use Your Touchpads Touchpads are used to control the security system from any location within or near your home. System Status Press System Status once to hear information about your system from the panel. Use when no one is home. Press twice to activate the Latchkey feature.
To subdisarm the system, enter the master access code. Panel will announce, system disarmed. The Disarm button on the panel will begin to blink.
Press the number of the lamp module you want to turn on. Press the number of the lamp module you want to turn off. Keychain Touchpad For any keypress on the Keychain Touchpad, hold the button until the indicator light blinks. If your installer programmed the Keychain Touchpad with no entry delay, and you armed the system with the Keychain Touchpad, you must disarm your system before entering the home to avoid causing an alarm.
If your installer programmed your system for Remote Touchpad Arming, you must enter your home to start the entry delay before you can use your Keychain Touchpad to disarm the system. Warning To avoid causing false alarms, check with your installer on how your touchpad options are programmed! Security system devices cannot compensate you for the loss of life LOCK Press once to arm doors and windows.
Note For any keypress on the Keychain Touchpad, hold the button until the indicator light blinks. Note Panic alarms need to be silenced from the panel, a remote handheld touchpad or another keychain touchpad. They cannot be silenced from the same keychain that activated the alarm.
The programming decals are visible when you open the panel cover see below. These decals are designed to make system programming easier for you. Always begin by entering your access code. Follow the prompts and flow arrows to complete the desired task. Notice the button flow diagrams following the Instruction Summary. Add Access Code and follow voice prompts. Figure 1. Opening the panel cover Programming Instructions Use the following instructions to access the programming buttons and programming decals.
Simon Security System System must be disarmed. Open the Panel Cover by pressing the plastic latch on the top of the panel. When you open the cover you will immediately be prompted by the panel voice to use the numbered keys to enter your ID.
Enter the Master Access Code. Depending on the button you pressed, the system will prompt you to continue by pressing other buttons on the panel. Access Codes Your security system has a master access code and access codes used for arming and disarming the panel.
The master code is used for disarming and programming your system. Access codes are generally used for children or as temporary codes for a babysitter or service personnel. Depending on the panel configuration, codes may be needed to arm the system. Check with the installer for your system configuration. Your system may be set up so that the master code or an access code is required when arming. If so, the panel will prompt you to enter a code when you attempt to arm the system.
Note Because different codes can be entered using the same button presses, you have to use caution when programming different codes. You need to ensure that one access code does not use the same button presses as other access codes. For example, if the master code is , do not program another code to be The panel would interpret these codes to be the same code.
Open the cover of the panel. The panel voice prompts you to Use numbered keys to enter ID. Enter your master access code using the numbered keys.
Press the access code button again to hear the next access code. Enter new numbers using the numbered keys. Access Code length is programmed by the installer. Close the panel cover. The panel voice responds with Access Code X deleted. Light Control You system has the ability to control lights from the panel. A specific light or group of lights can be programmed to turn on and off at designated times.
House Code Refers to a group of lights that can be controlled from the panel. Note The panel lists house codes A - O. Ask your installer what house code your lights are set up on. This is the House Code that was set by your installer. Press the Unit button. The panel responds with Unit 1 press again to change or select from control menu. Keep pressing the Unit button until the correct unit is selected. Press the Time button on the control menu. Press the Hours and Minutes buttons to set the correct on time.
Press Done. Press the Hours and Minutes buttons to set the correct off time. Panel will announce the unit number with the on and off times you just programmed. Programming Options The following table is a list of options you can change. When entering a single digit option number , you must type a zero before the number i. All option numbers must be 2 digits. Status beeps are any beeps including chime beeps that come from the panel.
Open panel cover. Panel announces, Use numbered keys to enter ID. Enter Access Code using the numbered keys. Panel announces, Please select from Start Menu. Press Add from the Start menu. Panel announces, Select from main menu. Press Option.
0コメント